config 1

keyboards/planck/planck.c

@@ -13,7 +13,7 @@ const keypos_t hand_swap_config[MATRIX_ROWS][MATRIX_COLS] = {
 __attribute__ ((weak))
 void matrix_init_kb(void) {
 	// Turn status LED on
-	#ifdef __AVR__
+	#if defined(__AVR__) && defined(DDRE)
 	DDRE |= (1<<6);
 	PORTE |= (1<<6);
 	#endif
@@ -26,4 +26,4 @@ const uint8_t music_map[MATRIX_ROWS][MATRIX_COLS] = LAYOUT_planck_grid(
 	24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35,
 	12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23,
 	 0,  1,  2,  3,  4,  5,  6,  7,  8,  9, 10, 11
-);
+);

keyboards/planck/thk/README.md

@@ -0,0 +1,71 @@
+# jj40
+
+![jj40](https://ae01.alicdn.com/kf/HTB18bq6bOERMeJjSspiq6zZLFXar.jpg?size=359506&height=562&width=750&hash=663a22d0109e2416ec8f54a7658686da)
+
+A compact 40% (12x4) ortholinear keyboard kit made and KPRepublic on AliExpress.
+
+Keyboard Maintainer: [QMK Community](https://github.com/qmk)  
+Hardware Supported: Atmega32A  
+Hardware Availability: [AliExpress](https://www.aliexpress.com/store/product/jj40-Custom-Mechanical-Keyboard-40-PCB-programmed-40-planck-layouts-bface-firmware-gh40/3034003_32828781103.html)
+
+Make example for this keyboard (after setting up your build environment):
+
+    make jj40:default:program
+
+See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.
+
+Note that this is a complete replacement for the firmware, so you won't be
+using Bootmapper Client to change any keyboard settings, since not all the
+USB report options are supported.
+
+In addition you may need the AVR toolchain and `bootloadHID` ([GitHub repo](https://github.com/whiteneon/bootloadHID)) for flashing:
+
+For macOS:
+```
+$ brew cask install crosspack-avr
+$ brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
+```
+
+For Linux:
+```
+$ sudo apt install libusb-dev
+$ wget https://www.obdev.at/downloads/vusb/bootloadHID.2012-12-08.tar.gz
+$ tar -xzf bootloadHID.2012-12-08.tar.gz
+$ cd bootloadHID.2012-12-08/commandline
+$ make
+$ sudo cp bootloadHID /usr/bin
+```
+
+In order to use the `./program` script, which can reboot the board into
+the bootloader, you'll need Python 2 with PyUSB installed:
+
+```
+$ pip install pyusb
+```
+
+If you prefer (or are having issues with a `program` flash), you can just build it (`make jj40:<keymap-name>` and flash the firmware (`.hex` file) directly with
+`bootloadHID` if you boot the board while holding down `Backspace` (`Top Right Key`) to keep it
+in the bootloader:
+
+```
+$ make jj40
+$ bootloadHID -r jj40_default.hex
+```
+
+For Windows 10:
+Windows sometimes doesn't recognize the jj40. The easiest way of flashing a new layout is probably using [HIDBootFlash](http://vusb.wikidot.com/project:hidbootflash).
+1. Go to Windows Device Manager and find the keyboard (plug it in while holding down `Backspace` (`Top Right Key`)). It can be found under Human Interface Devices or under Keyboards.
+2. Go to properties and the Details tab to find the hardware ID. You want the VID and the PID (code after the underscore). Plug them into HIDBootFlash and hit Find Device.
+3. Use `make jj40:<keymap-name>` to generate the .hex file in the qmk basis folder. Select the .hex file in HIDBootFlash and press Flash Device.
+
+
+## Troubleshooting
+
+1. Try plugging the board in while pressing `Backspace` (`Top Right Key`). This will force it
+   to boot only the bootloader without loading the firmware. Once this is
+   done, just reflash the board with the original firmware.
+2. Sometimes USB hubs can act weird, so try connecting the board directly
+   to your computer or plugging/unplugging the USB hub.
+3. If you get an error such as "Resource Unavailable" when attemting to flash
+   on Linux, you may want to compile and run `tools/usb_detach.c`. See `tools/README.md`
+   for more info.

keyboards/planck/thk/config.h

@@ -0,0 +1,60 @@
+/*
+Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include "config_common.h"
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#define VENDOR_ID       0x6060
+#define PRODUCT_ID      0x1001
+// TODO: share these strings with usbconfig.h
+// Edit usbconfig.h to change these.
+#define MANUFACTURER    OLKB
+#define PRODUCT         Planck
+
+/* matrix size */
+#define MATRIX_ROWS 4
+#define MATRIX_COLS 12
+
+#define MATRIX_ROW_PINS { A7, A6, A5, A4 }
+#define MATRIX_COL_PINS { D7, C2, C3, C4, C5, C6, C7, A3, A2, A1, A0, B0 }
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+#define BACKLIGHT_LEVELS 12
+// #define BACKLIGHT_BREATHING  // works, but BL_TOGG might not work
+
+#define TAPPING_TOGGLE 3
+
+#define NO_UART 1
+
+/* RGB underglow */
+// The RGB_DI_PIN value seems to be shared between all PS2AVRGB boards.
+// The same pin is used on the JJ40, at least.
+#define RGBLED_NUM 5
+#define RGB_DI_PIN E2 // NOTE: for PS2AVRGB boards, underglow commands are sent via I2C to 0xB0.
+#define RGBLIGHT_ANIMATIONS
+
+/* key combination for command */
+#define IS_COMMAND() (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
+
+#undef AUDIO_VOICES
+#undef C6_AUDIO
+
+#endif

keyboards/planck/thk/matrix.c

@@ -0,0 +1,145 @@
+/*
+Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <avr/io.h>
+#include <util/delay.h>
+
+#include "matrix.h"
+
+#ifndef DEBOUNCE
+#   define DEBOUNCE	5
+#endif
+
+
+// #define MATRIX_ROW_PINS { A7, A6, A5, A4 }
+// #define MATRIX_COL_PINS { D7, C2, C3, C4, C5, C6, C7, A3, A2, A1, A0, B0 }
+
+static uint8_t debouncing = DEBOUNCE;
+
+static matrix_row_t matrix[MATRIX_ROWS];
+static uint8_t matrix_debouncing[MATRIX_COLS];
+
+void matrix_init(void) {
+
+    MCUCSR = (1<<JTD);
+    MCUCSR = (1<<JTD);
+
+    //ADCSRA = 0;
+
+    // rows (input)
+    DDRA &= ~((1 << 7) | (1 << 6) | (1 << 5) | (1 << 4));
+    PORTA &= ~((1 << 7) | (1 << 6) | (1 << 5) | (1 << 4));
+
+    // cols (output)
+    DDRD |= ((1 << 7));
+    DDRC |= ((1 << 2) | (1 << 3) | (1 << 4) | (1 << 5) | (1 << 6) | (1 << 7));
+    DDRA |= ((1 << 3) | (1 << 2) | (1 << 1) | (1 << 0));
+    DDRB |= ((1 << 0));
+
+    PORTD &= ~((1 << 7));
+    PORTC &= ~((1 << 2) | (1 << 3) | (1 << 4) | (1 << 5) | (1 << 6) | (1 << 7));
+    PORTA &= ~((1 << 3) | (1 << 2) | (1 << 1) | (1 << 0));
+    PORTB &= ~((1 << 0));
+
+    // initialize matrix state: all keys off
+    for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
+        matrix[row] = 0x00;
+    }
+    for (uint8_t col = 0; col < MATRIX_COLS; col++) {
+        matrix_debouncing[col] = 0x00;
+    }
+
+    matrix_init_quantum();
+}
+
+uint8_t matrix_scan(void) {
+
+    for (uint8_t c = 0; c < MATRIX_COLS; c++) {
+        switch (c) {
+          case 0:  PORTD |= (1 << 7); break;
+          case 1:  PORTC |= (1 << 2); break;
+          case 2:  PORTC |= (1 << 3); break;
+          case 3:  PORTC |= (1 << 4); break;
+          case 4:  PORTC |= (1 << 5); break;
+          case 5:  PORTC |= (1 << 6); break;
+          case 6:  PORTC |= (1 << 7); break;
+          case 7:  PORTA |= (1 << 3); break;
+          case 8:  PORTA |= (1 << 2); break;
+          case 9:  PORTA |= (1 << 1); break;
+          case 10: PORTA |= (1 << 0); break;
+          case 11: PORTB |= (1 << 0); break;
+        }
+        _delay_us(5);
+
+        uint8_t current_col = (
+           ((PINA & (1 << 7)) ? 1 : 0 ) |
+          (((PINA & (1 << 6)) ? 1 : 0 ) << 1) |
+          (((PINA & (1 << 5)) ? 1 : 0 ) << 2) |
+          (((PINA & (1 << 4)) ? 1 : 0 ) << 3)
+        );
+
+        switch (c) {
+          case 0:  PORTD &= ~(1 << 7); break;
+          case 1:  PORTC &= ~(1 << 2); break;
+          case 2:  PORTC &= ~(1 << 3); break;
+          case 3:  PORTC &= ~(1 << 4); break;
+          case 4:  PORTC &= ~(1 << 5); break;
+          case 5:  PORTC &= ~(1 << 6); break;
+          case 6:  PORTC &= ~(1 << 7); break;
+          case 7:  PORTA &= ~(1 << 3); break;
+          case 8:  PORTA &= ~(1 << 2); break;
+          case 9:  PORTA &= ~(1 << 1); break;
+          case 10: PORTA &= ~(1 << 0); break;
+          case 11: PORTB &= ~(1 << 0); break;
+        }
+
+        if (matrix_debouncing[c] != current_col) {
+            matrix_debouncing[c] = current_col;
+            debouncing = DEBOUNCE;
+        }
+    }
+
+    if (debouncing) {
+        if (--debouncing) {
+            _delay_ms(1);
+        } else {
+            for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+                matrix[i] = 0;
+                for (uint8_t j = 0; j < MATRIX_COLS; j++) {
+                    matrix[i] |= (((matrix_debouncing[j] & (1 << i)) ? 1L : 0 ) << j);
+                }
+            }
+        }
+    }
+
+    matrix_scan_quantum();
+
+    return 1;
+}
+
+inline matrix_row_t matrix_get_row(uint8_t row) {
+    return matrix[row];
+}
+
+void matrix_print(void) {
+}
+
+__attribute__ ((weak))
+void matrix_init_user(void) { }
+
+__attribute__ ((weak))
+void matrix_scan_user(void) { }

keyboards/planck/thk/rules.mk

@@ -0,0 +1,55 @@
+# Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
+#
+# This program is free software: you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation, either version 2 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program.  If not, see <http://www.gnu.org/licenses/>.
+
+# MCU name
+MCU = atmega32a
+PROTOCOL = VUSB
+
+# unsupported features for now
+NO_UART = yes
+NO_SUSPEND_POWER_DOWN = yes
+
+# processor frequency
+F_CPU = 16000000
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = bootloadHID
+
+# build options
+BOOTMAGIC_ENABLE = no
+MOUSEKEY_ENABLE = no
+EXTRAKEY_ENABLE = yes
+CONSOLE_ENABLE = no
+COMMAND_ENABLE = yes
+KEY_LOCK_ENABLE = yes
+NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+AUDIO_ENABLE = no
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+
+OPT_DEFS = -DDEBUG_LEVEL=0
+
+# custom matrix setup
+CUSTOM_MATRIX = yes
+SRC = matrix.c
+
+# programming options
+PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex
+
+LAYOUTS = ortho_4x12 planck_mit planck_grid

keyboards/planck/thk/thk.c

@@ -0,0 +1,45 @@
+/* Copyright 2018 Jack Humbert <jack.humb@gmail.com>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include "thk.h"
+
+void matrix_init_kb(void) {
+
+  DDRD |= (1<<5);
+    //PORTD |= (1<<5);
+  matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+  matrix_scan_user();
+}
+
+static uint8_t keys_pressed = 0;
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+  if (record->event.pressed) {
+    keys_pressed++;
+  } else {
+    keys_pressed--;
+  }
+
+  if (keys_pressed) {
+    PORTD |= (1<<5);
+  } else {
+    PORTD &= ~(1<<5);
+  }
+  return process_record_user(keycode, record);
+}

keyboards/planck/thk/thk.h

@@ -0,0 +1,19 @@
+/* Copyright 2018 Jack Humbert <jack.humb@gmail.com>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+#include "planck.h"

keyboards/planck/thk/tools/README.md

@@ -0,0 +1,16 @@
+# JJ40 Tools
+
+## usb_detach.c
+
+When trying to flash on Linux, you may encounter a "Resource Unavailable" error. This means that Linux's HID driver has taken exclusive control of the keyboard, and the program script can't flash it.
+This program can force Linux to give up a device, so that the programming script can reset it.
+
+### To compile:
+```
+gcc usb_detach.c -o usb_detach
+```
+
+### To run:
+1. Use `lsusb` to discover the Bus and Device numbers for your keyboard.
+2. Run the program: `sudo ./usb_detach /dev/bus/usb/<BUS>/<DEVICE>`.
+3. Build and program the firmware as normal.

keyboards/planck/thk/tools/usb_detach.c

@@ -0,0 +1,33 @@
+/* Found at https://www.linuxquestions.org/questions/linux-hardware-18/how-to-unclaim-usb-device-558138/#post3406986 */
+#include <stdio.h>
+#include <sys/types.h>
+#include <sys/stat.h>
+#include <fcntl.h>
+#include <linux/ioctl.h>
+#include <linux/usbdevice_fs.h>
+
+int main(int argc, char**argv)
+{
+        struct usbdevfs_ioctl command;
+        int ret;
+        int fd;
+        int i;
+        if (argc>1) {
+                fd = open(argv[1],O_RDWR);
+                if (fd<1){
+                        perror("unable to open file");
+                        return 1;
+                }
+                for (i=0;i<255;i++){ // hack: should fetch how many interface there is.
+                        command.ifno = i;
+                        command.ioctl_code = USBDEVFS_DISCONNECT;
+                        command.data = NULL;
+                        ret = ioctl(fd, USBDEVFS_IOCTL, &command);
+                        if(ret!=-1)
+                                printf("un claimed interface %d %d\n",i,ret);
+                }
+        } else {
+                printf ("usage: %s /dev/bus/usb/BUS/DEVICE\n",argv[0]);
+                printf("Release all interfaces of this usb device for usage in virtualisation\n");
+        }
+}

keyboards/planck/thk/usbconfig.h

@@ -0,0 +1,397 @@
+/* Name: usbconfig.h
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Author: Christian Starkjohann
+ * Creation Date: 2005-04-01
+ * Tabsize: 4
+ * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
+ * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
+ */
+
+#ifndef __usbconfig_h_included__
+#define __usbconfig_h_included__
+
+#include "config.h"
+
+/*
+General Description:
+This file is an example configuration (with inline documentation) for the USB
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
+also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
+wire the lines to any other port, as long as D+ is also wired to INT0 (or any
+other hardware interrupt, as long as it is the highest level interrupt, see
+section at the end of this file).
+*/
+
+/* ---------------------------- Hardware Config ---------------------------- */
+
+#define USB_CFG_IOPORTNAME      D
+/* This is the port where the USB bus is connected. When you configure it to
+ * "B", the registers PORTB, PINB and DDRB will be used.
+ */
+#define USB_CFG_DMINUS_BIT      3
+/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
+ * This may be any bit in the port.
+ */
+#define USB_CFG_DPLUS_BIT       2
+/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
+ * This may be any bit in the port. Please note that D+ must also be connected
+ * to interrupt pin INT0! [You can also use other interrupts, see section
+ * "Optional MCU Description" below, or you can connect D- to the interrupt, as
+ * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
+ * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
+ * markers every millisecond.]
+ */
+#define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
+ * frequency. All other rates require a precision of 2000 ppm and thus a
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC       0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
+ */
+
+/* ----------------------- Optional Hardware Config ------------------------ */
+
+/* #define USB_CFG_PULLUP_IOPORTNAME   D */
+/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
+ * V+, you can connect and disconnect the device from firmware by calling
+ * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
+ * This constant defines the port on which the pullup resistor is connected.
+ */
+/* #define USB_CFG_PULLUP_BIT          4 */
+/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
+ * above) where the 1.5k pullup resistor is connected. See description
+ * above for details.
+ */
+
+/* --------------------------- Functional Range ---------------------------- */
+
+#define USB_CFG_HAVE_INTRIN_ENDPOINT    1
+/* Define this to 1 if you want to compile a version with two endpoints: The
+ * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
+ * number).
+ */
+#define USB_CFG_HAVE_INTRIN_ENDPOINT3   1
+/* Define this to 1 if you want to compile a version with three endpoints: The
+ * default control endpoint 0, an interrupt-in endpoint 3 (or the number
+ * configured below) and a catch-all default interrupt-in endpoint as above.
+ * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
+ */
+#define USB_CFG_EP3_NUMBER              3
+/* If the so-called endpoint 3 is used, it can now be configured to any other
+ * endpoint number (except 0) with this macro. Default if undefined is 3.
+ */
+/* #define USB_INITIAL_DATATOKEN           USBPID_DATA1 */
+/* The above macro defines the startup condition for data toggling on the
+ * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
+ * Since the token is toggled BEFORE sending any data, the first packet is
+ * sent with the oposite value of this configuration!
+ */
+#define USB_CFG_IMPLEMENT_HALT          0
+/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
+ * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
+ * it is required by the standard. We have made it a config option because it
+ * bloats the code considerably.
+ */
+#define USB_CFG_SUPPRESS_INTR_CODE      0
+/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
+ * want to send any data over them. If this macro is defined to 1, functions
+ * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
+ * you need the interrupt-in endpoints in order to comply to an interface
+ * (e.g. HID), but never want to send any data. This option saves a couple
+ * of bytes in flash memory and the transmit buffers in RAM.
+ */
+#define USB_CFG_INTR_POLL_INTERVAL      1
+/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
+ * interval. The value is in milliseconds and must not be less than 10 ms for
+ * low speed devices.
+ */
+#define USB_CFG_IS_SELF_POWERED         0
+/* Define this to 1 if the device has its own power supply. Set it to 0 if the
+ * device is powered from the USB bus.
+ */
+// max power draw with maxed white underglow measured at 120 mA (peaks)
+#define USB_CFG_MAX_BUS_POWER           100
+/* Set this variable to the maximum USB bus power consumption of your device.
+ * The value is in milliamperes. [It will be divided by two since USB
+ * communicates power requirements in units of 2 mA.]
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITE      1
+/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
+ * transfers. Set it to 0 if you don't need it and want to save a couple of
+ * bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_READ       0
+/* Set this to 1 if you need to send control replies which are generated
+ * "on the fly" when usbFunctionRead() is called. If you only want to send
+ * data from a static buffer, set it to 0 and return the data from
+ * usbFunctionSetup(). This saves a couple of bytes.
+ */
+#define USB_CFG_IMPLEMENT_FN_WRITEOUT   0
+/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
+ * You must implement the function usbFunctionWriteOut() which receives all
+ * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
+ * can be found in 'usbRxToken'.
+ */
+#define USB_CFG_HAVE_FLOWCONTROL        0
+/* Define this to 1 if you want flowcontrol over USB data. See the definition
+ * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
+ * usbdrv.h.
+ */
+#define USB_CFG_DRIVER_FLASH_PAGE       0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
+#define USB_CFG_LONG_TRANSFERS          0
+/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
+ * in a single control-in or control-out transfer. Note that the capability
+ * for long transfers increases the driver size.
+ */
+/* #define USB_RX_USER_HOOK(data, len)     if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
+/* This macro is a hook if you want to do unconventional things. If it is
+ * defined, it's inserted at the beginning of received message processing.
+ * If you eat the received message and don't want default processing to
+ * proceed, do a return after doing your things. One possible application
+ * (besides debugging) is to flash a status LED on each packet.
+ */
+/* #define USB_RESET_HOOK(resetStarts)     if(!resetStarts){hadUsbReset();} */
+/* This macro is a hook if you need to know when an USB RESET occurs. It has
+ * one parameter which distinguishes between the start of RESET state and its
+ * end.
+ */
+/* #define USB_SET_ADDRESS_HOOK()              hadAddressAssigned(); */
+/* This macro (if defined) is executed when a USB SET_ADDRESS request was
+ * received.
+ */
+#define USB_COUNT_SOF                   1
+/* define this macro to 1 if you need the global variable "usbSofCount" which
+ * counts SOF packets. This feature requires that the hardware interrupt is
+ * connected to D- instead of D+.
+ */
+/* #ifdef __ASSEMBLER__
+ * macro myAssemblerMacro
+ *     in      YL, TCNT0
+ *     sts     timer0Snapshot, YL
+ *     endm
+ * #endif
+ * #define USB_SOF_HOOK                    myAssemblerMacro
+ * This macro (if defined) is executed in the assembler module when a
+ * Start Of Frame condition is detected. It is recommended to define it to
+ * the name of an assembler macro which is defined here as well so that more
+ * than one assembler instruction can be used. The macro may use the register
+ * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
+ * immediately after an SOF pulse may be lost and must be retried by the host.
+ * What can you do with this hook? Since the SOF signal occurs exactly every
+ * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
+ * designs running on the internal RC oscillator.
+ * Please note that Start Of Frame detection works only if D- is wired to the
+ * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
+ */
+#define USB_CFG_CHECK_DATA_TOGGLING     0
+/* define this macro to 1 if you want to filter out duplicate data packets
+ * sent by the host. Duplicates occur only as a consequence of communication
+ * errors, when the host does not receive an ACK. Please note that you need to
+ * implement the filtering yourself in usbFunctionWriteOut() and
+ * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
+ * for each control- and out-endpoint to check for duplicate packets.
+ */
+#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
+/* define this macro to 1 if you want the function usbMeasureFrameLength()
+ * compiled in. This function can be used to calibrate the AVR's RC oscillator.
+ */
+#define USB_USE_FAST_CRC                0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
+
+/* -------------------------- Device Description --------------------------- */
+
+#define USB_CFG_VENDOR_ID       (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
+/* USB vendor ID for the device, low byte first. If you have registered your
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_ID       (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
+/* This is the ID of the product, low byte first. It is interpreted in the
+ * scope of the vendor ID. If you have registered your own VID with usb.org
+ * or if you have licensed a PID from somebody else, define it here. Otherwise
+ * you may use one of obdev's free shared VID/PID pairs. See the file
+ * USB-IDs-for-free.txt for details!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define USB_CFG_DEVICE_VERSION  0x00, 0x02
+/* Version number of the device: Minor number first, then major number.
+ */
+#define USB_CFG_VENDOR_NAME     'O','L','K','B'
+#define USB_CFG_VENDOR_NAME_LEN 4
+/* These two values define the vendor name returned by the USB device. The name
+ * must be given as a list of characters under single quotes. The characters
+ * are interpreted as Unicode (UTF-16) entities.
+ * If you don't want a vendor name string, undefine these macros.
+ * ALWAYS define a vendor name containing your Internet domain name if you use
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
+ * details.
+ */
+#define USB_CFG_DEVICE_NAME     'P', 'l', 'a', 'n', 'c', 'k'
+#define USB_CFG_DEVICE_NAME_LEN 6
+/* Same as above for the device name. If you don't want a device name, undefine
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
+ * you use a shared VID/PID.
+ */
+/*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
+/*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
+/* Same as above for the serial number. If you don't want a serial number,
+ * undefine the macros.
+ * It may be useful to provide the serial number through other means than at
+ * compile time. See the section about descriptor properties below for how
+ * to fine tune control over USB descriptors such as the string descriptor
+ * for the serial number.
+ */
+#define USB_CFG_DEVICE_CLASS        0
+#define USB_CFG_DEVICE_SUBCLASS     0
+/* See USB specification if you want to conform to an existing device class.
+ * Class 0xff is "vendor specific".
+ */
+#define USB_CFG_INTERFACE_CLASS     3   /* HID */
+#define USB_CFG_INTERFACE_SUBCLASS  1   /* Boot */
+#define USB_CFG_INTERFACE_PROTOCOL  1   /* Keyboard */
+/* See USB specification if you want to conform to an existing device class or
+ * protocol. The following classes must be set at interface level:
+ * HID class is 3, no subclass and protocol required (but may be useful!)
+ * CDC class is 2, use subclass 2 and protocol 1 for ACM
+ */
+#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    0
+/* Define this to the length of the HID report descriptor, if you implement
+ * an HID device. Otherwise don't define it or define it to 0.
+ * If you use this define, you must add a PROGMEM character array named
+ * "usbHidReportDescriptor" to your code which contains the report descriptor.
+ * Don't forget to keep the array and this define in sync!
+ */
+
+/* #define USB_PUBLIC static */
+/* Use the define above if you #include usbdrv.c instead of linking against it.
+ * This technique saves a couple of bytes in flash memory.
+ */
+
+/* ------------------- Fine Control over USB Descriptors ------------------- */
+/* If you don't want to use the driver's default USB descriptors, you can
+ * provide our own. These can be provided as (1) fixed length static data in
+ * flash memory, (2) fixed length static data in RAM or (3) dynamically at
+ * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
+ * information about this function.
+ * Descriptor handling is configured through the descriptor's properties. If
+ * no properties are defined or if they are 0, the default descriptor is used.
+ * Possible properties are:
+ *   + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
+ *     at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
+ *     used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
+ *     you want RAM pointers.
+ *   + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
+ *     in static memory is in RAM, not in flash memory.
+ *   + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
+ *     the driver must know the descriptor's length. The descriptor itself is
+ *     found at the address of a well known identifier (see below).
+ * List of static descriptor names (must be declared PROGMEM if in flash):
+ *   char usbDescriptorDevice[];
+ *   char usbDescriptorConfiguration[];
+ *   char usbDescriptorHidReport[];
+ *   char usbDescriptorString0[];
+ *   int usbDescriptorStringVendor[];
+ *   int usbDescriptorStringDevice[];
+ *   int usbDescriptorStringSerialNumber[];
+ * Other descriptors can't be provided statically, they must be provided
+ * dynamically at runtime.
+ *
+ * Descriptor properties are or-ed or added together, e.g.:
+ * #define USB_CFG_DESCR_PROPS_DEVICE   (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
+ *
+ * The following descriptors are defined:
+ *   USB_CFG_DESCR_PROPS_DEVICE
+ *   USB_CFG_DESCR_PROPS_CONFIGURATION
+ *   USB_CFG_DESCR_PROPS_STRINGS
+ *   USB_CFG_DESCR_PROPS_STRING_0
+ *   USB_CFG_DESCR_PROPS_STRING_VENDOR
+ *   USB_CFG_DESCR_PROPS_STRING_PRODUCT
+ *   USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
+ *   USB_CFG_DESCR_PROPS_HID
+ *   USB_CFG_DESCR_PROPS_HID_REPORT
+ *   USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
+ *
+ * Note about string descriptors: String descriptors are not just strings, they
+ * are Unicode strings prefixed with a 2 byte header. Example:
+ * int  serialNumberDescriptor[] = {
+ *     USB_STRING_DESCRIPTOR_HEADER(6),
+ *     'S', 'e', 'r', 'i', 'a', 'l'
+ * };
+ */
+
+#define USB_CFG_DESCR_PROPS_DEVICE                  0
+#define USB_CFG_DESCR_PROPS_CONFIGURATION           USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_CONFIGURATION           0
+#define USB_CFG_DESCR_PROPS_STRINGS                 0
+#define USB_CFG_DESCR_PROPS_STRING_0                0
+#define USB_CFG_DESCR_PROPS_STRING_VENDOR           0
+#define USB_CFG_DESCR_PROPS_STRING_PRODUCT          0
+#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    0
+#define USB_CFG_DESCR_PROPS_HID                     USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID                     0
+#define USB_CFG_DESCR_PROPS_HID_REPORT              USB_PROP_IS_DYNAMIC
+//#define USB_CFG_DESCR_PROPS_HID_REPORT              0
+#define USB_CFG_DESCR_PROPS_UNKNOWN                 0
+
+#define usbMsgPtr_t unsigned short
+/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
+ * a scalar type here because gcc generates slightly shorter code for scalar
+ * arithmetics than for pointer arithmetics. Remove this define for backward
+ * type compatibility or define it to an 8 bit type if you use data in RAM only
+ * and all RAM is below 256 bytes (tiny memory model in IAR CC).
+ */
+
+/* ----------------------- Optional MCU Description ------------------------ */
+
+/* The following configurations have working defaults in usbdrv.h. You
+ * usually don't need to set them explicitly. Only if you want to run
+ * the driver on a device which is not yet supported or with a compiler
+ * which is not fully supported (such as IAR C) or if you use a differnt
+ * interrupt than INT0, you may have to define some of these.
+ */
+/* #define USB_INTR_CFG            MCUCR */
+/* #define USB_INTR_CFG_SET        ((1 << ISC00) | (1 << ISC01)) */
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         GIMSK */
+/* #define USB_INTR_ENABLE_BIT     INT0 */
+/* #define USB_INTR_PENDING        GIFR */
+/* #define USB_INTR_PENDING_BIT    INTF0 */
+/* #define USB_INTR_VECTOR         INT0_vect */
+
+/* Set INT1 for D- falling edge to count SOF */
+/* #define USB_INTR_CFG            EICRA */
+#define USB_INTR_CFG_SET        ((1 << ISC11) | (0 << ISC10))
+/* #define USB_INTR_CFG_CLR        0 */
+/* #define USB_INTR_ENABLE         EIMSK */
+#define USB_INTR_ENABLE_BIT     INT1
+/* #define USB_INTR_PENDING        EIFR */
+#define USB_INTR_PENDING_BIT    INTF1
+#define USB_INTR_VECTOR         INT1_vect
+
+#endif /* __usbconfig_h_included__ */