qmk_firmware_custom/keyboard/hhkb

Alternative Controller for HHKB Pro

I wanted to add some features like vi cursor and mouse keys to my HHKB but its controller is not programmable and firmware source code is not open, of course. This means customizing this keyboard needs to replace original controller with programmable one. For this purpose I used PJRC Teensy++ as alternative controller.

My keyboard firmware source tree is here: http://github.com/tmk/tmk_keyboard See directory keyboard/hhkb to build firmware for HHKB.

##Features

• Customizable keymap
• More keymap layers(more Fn keys)
• Mouse keys
• USB NKRO

###Pros

• Without PCB trace cutting, case mod or any destructives
• Can keep original controller intact
• Can change all HHKB behaviour as you like

###Cons

• Void your warranty
• Lose USB hub function in case of Pro2

##DISCLAIMER I'm not a professional of electronics or MCU programming. This may damage your HHKB. And my English writing is poor, I'm not sure I can convey my notions accurately.

##Build Firmware You can choose some combination of MCU and USB protocol stack.

Teensy++(AVR USB family) with LUFA

1. Edit matrix.c to use your pin configuration. See doc/HHKB.txt for detail.

2. Edit keymap.c to use your favoirte keymap.

3. Edit Makefile if you want to use other MCU than Teensy++ 2.0.

4. Build firmware binary file: $ make -f Makefile.lufa

5. Program MCU with PJRC Teensy Loader tool. If you install command line version of the loader just run: $ make -f Makefile.lufa teensy

###AVR Mega with V-USB Follow below if you want to use AVR with V-USB as .

1. Edit matrix.c to use your pin configuration. See doc/HHKB.txt for detail.

2. Edit keymap.c to use your favoirte keymap.

3. Edit usbconfig.h to configure V-USB options.

4. Edit Makefile.vusb to define MCU and F_CPU.

5. Build firmware binary file: $ make -f Makefile.vusb

6. Program MCU with AVR programmer like AVRISPmkII. If you already have USBaspLoader on MCU just run: $ make -f Makefile.vusb program

###How to Customize Keymap Later... See keymap.c.

##Hardware

###Teensy++ installation Angled USB mini B adapter is used to install Teensy++ laterally.

Bread baord wires are used to connect Teensy++.

###PJRC Teensy++ 2.0 connection

                        +---------------+
                        |   Teensy++    |
                        |               |
                        |               |        HHKB
                        |               |        ~~~~
                        |          PB0-2|------->ROW(6-8)
                        |          PB3-5|------->COL(9-11)
                        |            PB6|------->ENABLE(12)
                        |            PE6|<-------KEY(4)
                        |            PE7|------->PREV(5)
                        |               |
                        |               |
                        |               |
                        +---------------+

###V-USB circuit

                +---+   +---------------+
USB            GND  |   |   ATmega168   |
~~~                 C3  |               |
5V <-------+--------+---|Vcc,AVCC       |        HHKB
           R1           |               |        ~~~~
D- <----+--+-----R2-----|INT1      PB2-4|------->ROW(6-8)
D+ <----|---+----R3-----|INT0      PC0-2|------->COL(9-11)
        Z1  Z2          |            PC3|------->ENABLE(12)
GND<----+---+-----------|GND         PB0|<-------KEY(4)
                        |            PB1|------->PREV(5)
                        |               |
            GND+-C2--+--|XTAL1       RXD|------->Debug Console
                     X1 |            TXD|<-------Debug Console
            GND+-C3--+--|XTAL2       RST|---SW--+GND
                        +---------------+
R1:     1.5K Ohm
R2,R3:  68 Ohm
Z1,Z2:  Zener 3.6V
C1,C2:  22pF
C3:     0.1uF
X1:     Crystal 20MHz(16MHz/12MHz)
SW:     Push Switch(Optional for bootloader)